The R1 router has to examine the destination IP address to determine how the packet is to be routed. If the packet is to be routed out another interface, as is the case with R1, the router strips the current Layer 2 header and attaches a new Layer 2 header. When R2 determines that the packet is to be sent out the LAN interface, R2 removes the Layer 2 header received from the serial link and attaches a new Ethernet header before transmitting the packet. On which two routers would a default static route be configured?

Author:Vudozahn Kajijind
Language:English (Spanish)
Published (Last):1 July 2017
PDF File Size:17.42 Mb
ePub File Size:5.46 Mb
Price:Free* [*Free Regsitration Required]

System messages will be forwarded to the number following the logging trap argument. To provide statistics on packets that are flowing through a Cisco device. PoliceDept config ip route 0. A network administrator is configuring an ACL with the command access-list 10 permit Dynamic Mode Incorrect Network: An administrator corrrection examining the message in a syslog server.

What is a basic function of the Cisco Borderless Architecture access layer? Match the router memory type that provides the primary storage for the router feature. Layers minimize the number of devices on any one tier that share a single point of failure.

Which two statements are correct based on the output as shown in the exhibit? The branch networks are not routed with OSPFv2. When a violation occurs, which violation mode that is configured on an interface will cause packets with an unknown source address to be dropped with no notification sent?

Traffic that is destined for correctino All IOS device configurations should be completed from a direct terminal connection to the device console. Match each borderless switched network principle to its description. During the Quiz End of Quiz. All hosts and router interfaces are configured correctly. What caused the following error message to appear? It allows sites to use private IPv4 addresses, and thus hides the internal addressing structure from hosts on public IPv4 networks.

Sign In with your ProProfs account. What will be the result of adding the command ip dhcp excluded-address Configure single-area OSPFv2 to route between all internal networks. Do not use the default keyword in the commands you use to do this.

Instructions All configurations must be performed through a direct terminal connection to the device consoles. Refer to the exhibit. This provides quality of service and additional security. The computers used by the network administrators for a school are on the Fire config ip route Central config ip nat inside source static Issue the command network System messages that exist in levels must be forwarded to a specific logging server.

CCNA 2 V6. Stub router corretion to the rest of the corporate or campus network. Which command should be entered to prepare this port for the task? These values may include certain IP addresses, passwords, interface descriptions, banner text, and other values. Which change should be made to the static route command so that traffic will only use the OSPF link when it is up? What is causing this problem? Select a Match hierarchical exanen resiliency — flexibility. All questions 5 questions corrrection questions 7 questions 8 questions 9 questions 10 questions 11 questions 12 questions 13 questions 14 questions 15 questions 16 questions 17 questions 18 questions 19 questions 20 questions 21 questions 22 questions 23 questions 24 questions 25 questions 26 questions 27 questions 28 questions 29 questions 30 questions 31 questions 32 questions 33 questions 34 questions 35 questions 36 questions 37 questions 38 questions 39 questions 40 questions 41 questions 42 questions 43 questions 44 questions 45 questions 46 questions 47 questions 48 questions 49 questions 50 questions.

This is a notification message for a normal but significant condition. Many of these tasks, especially those related to device security, are essential elements of a network configuration. Your ACL should be placed in the most efficient location possible to conserve network bandwidth and device processing resources. In those cases, create the values that you need to complete the requirements. A host with an invalid IP address was connected to a switch port that was previously unused.

A network administrator issues the show ip nat translations command to check the NAT configurations. Issue the command ip helper-address Another switch was connected to this switch port with the wrong cable. All running configurations are saved at the start and close of every business day.

Traffic will not be routed from clients with addresses between A company has an internal network of The host with the address TOP 10 Related.



Tezragore A network engineer is interested in obtaining specific information relevant to the operation of both distribution and access layer Cisco devices. Which port security configuration enabled this? A small business uses VLANs 2, 3, 4, and 5 between two switches that have a trunk link between them. PoliceDept config-router network Fire config router ospf 10 Fire config-router router-id 3.


ccna 2 examain pdf v4


Related Articles